Drawing No

Description

Date

18500		Arrangement of Firegrate and Ashpan	28.8.36
18501
18502	A	Inspection Plate (lubricator drive)	26.8.36
	B	Lubricator Drive Spindle	_
	C	Lubricator Carrier Bracket	_
	D	Bracket For Lubricator pipe	_
	E	Elbow for Mech Lubricator	_
18503		Pusher Cylinder	26.5.36
18504	A	Cross Over Sheet for Vacuum Brake control	17.8.36
	B	Bracket for Sand Valve Ejector	_
	C	Throttle Direction Change Spindle	_
	D/E	Bearing Housing Pedestal	_
	F	Throttle Valve Bell Crank	_
	G	Guide Block for Throttle Sand Rods	_
18505		Arrangement of Lubricator Cylinders	28.8.36
18506	A	Engine Suspension housing	27.8.36
	B	Engine Suspension housing cover	_
18507		Arrangement and Detail of Frame	31.1.36
18508		Arrangement of Water Level Gauge	9.9.36
18508 B		Arrangement of Water Level Gauge	9.9.36
18509		Special Coupling Nipple (lub. Valve chest)	2.9.36
	B	Coupling Nipple (lubricator pipe)	_
	D/E	Coupling Nipple (lubricator pipe)	_
18510		3/16" Bore Superflexit	3.9.36
18511		Arrangement of S4 waggon	17.12.34
18512		Arrangement of Control Column	6.9.36
18513		Arrangement of Boiler Compartment	4.9.36
18514		Arrangement of Mileometer	5.9.36
18515	A	Base plate for Worthington Simspon pump	5.9.36
	B	Dust Cover for 'Float ex' Brg Type 'M'	_
	C	7/8" Gas Plug	_
	D	Blanking Off Plate for Pump Facing	_
18516		Coachbuilders Drawing	8.9.36
18517		Firebox Protection Plate	10.9.36
18518	A/B	Arrangement and Detail of Drilling in Front Mudguards	30.9.36
		Arrangement and Detail of Drilling in Rear Mudguards	_
18519	A	Tank Filler Base	10.9.36
	B	Water Tank Vent Rise	_
	C	Carch for Filler Lid	_
	D/G	Special Pin for Catch	_
	E	Tank Filler Base Joint	_
	F	Clamp for Filler joint	_
	H	Special Control Rod Jaw	_
18520		Control Shaft	10.9.36
18521	A	Steam Pipe to Engine	14.9.36
	B	Exhaust Pipe from Manifold	_
	C	Exhaust Pipe (vertical)	_
	D	Assembly of Vertical Steam Pipe	_
	E	Steam Pipe Suspension plate	_
	F	Exhaust Pipe Suspension plate	_
18522		Feed Pump Body	27.4.33
18523		Control Shaft	15.9.36
18524	A	Steam Pipe	15.9.36
	B	Exhaust Pipe	_
	C	Injector Carrying plate	_
	D	Injector Carrying angle	_
		Exhaust Pipe	_
	F	Pump Stay	_
18525	A	Side lamp Bracket Distance Piece	21.3.36
	B	Distance Piece Stiffening plate	_
	C	Extra Drilling in Apron Plate for Side Lamp Bracket	_
	D	Side Lamp suap??? Bracket	_
	E	Turntable Ring - top	_
	F	Turntable Ring - bottom	_
18526		Control Rods
		Control Shaft	_
18527		Arrangement of Articulated Tank vehicle	28.9.36
18528		Exhaust Feed Heater Body	2.10.36
18529		Drilling Required in Injector	5.10.36
18530	A	Exhaust Feed Heater Base	5.10.36
	B	Exhaust Feed Heater outlet	_
	C/D	Exhaust Feed Heater Cover	_
18531		Arrangement of Water Tank	25.10.36
18532	A	Cross Tube	6.10.36
	B	Cross Tube bracket	_
	C	Cross Tube plug	_
	D	Support Plate for Fan Bed-plate	_
18533		Arrangement of Controls	2.12.36
18534		Holes in Leading Frame	7.10.36
18535		Underframe Drilling
18536	A	Exhaust Feed Heater Baffle	12.10.36
	B	Exhaust Feed Heater Outlet End Tube plate	_
	C	Exhaust Feed heater Inlet End Tubeplate	_
18537	A	Exhaust Feed heater outlet end	13.10.36
	B	Exhaust Feed Heater gland	_
	C	Exhaust Relief Valve Elbow	_
	D	Cap Nut for Exhaust Feed Heater outlet	_
	E	Exhaust Feed heater outlet end	_
	F	Exhaust Feed Heater tube	_
18538		Arrangement of Exhaust Feed heater	14.10.36
18539		Arrangement of Road Her??er Trailer	23.10.36
18540		Arrangement of Two-wheeled trailer	15.10.36
18541		Arrangement of Trailer frame	13.10.36
18542	A	Arrangement of Turntable	17.10.36
	B	Engine Support channel - front	_
	D	Engine Support plate	_
18543		Arrangement of Tractor unit	21.10.35
18544	A	Outline Arrangement of S6 with 9 ton acid tank	22.10.36
	B	Outline Arrangement of S6 with 11 ton acid tank	_
18545	A	Control Cross Shaft Bracket	22.10.36
		Cross Shaft Bracket Centre	_
	D	Cross Shaft Bracket (artic ld end)	_
18546	A	Spray Pipe flange	23.10.36
	B	Spray Pipe extn flange	_
	C	Spray Pipe Return Bend	_
	D	Spray Pipe joint washer	_
	E	Spray Pipe Flange dowel pin	_
18547		Arrangement of SD 6 Wheeler with 35 CWT steam crane	23.10.36
18548		Arrangement of Spray Pipe joint	28.10.36
18549	A	Steam Collector pipe	27.10.36
	B	Collector Pipe elbow CANCELLED	_
	C	Collector Pipe Hook bolt	_
18550		Sentinel Patent Water Tube boiler	28.10.36
18551		Arrangement of Rocking Grate and Operating gear	5.10.36
18552		Arrangement of Firing End Fittings	15.10.36
18553		Back Plate and Boiler support	12.10.36
18554 AA		Firing End Plate and Boiler support	15.7.37
18554 BB		Firing End Plate and Boiler support	15..10.37
18555 U		Arrangement of Smoke-box	16.10.36
18555 T		Arrangement and Detail of Smokebox and Chimney	15.7.36
18556		Boiler Top Fittings	14.6.36
18557	A/B/C	CAN't Read Description	22.6.36
		Firedoor Shaft	_
	E/F	Firedoor spindle	_
	?	Firedoor Handle stop	_
	h/j	CAN't Read Description	_
	k	Firedoor sprine	_
	L/M	Feed Tray Support	_
18558		Arrangement of DG6 on Pneu Tyres with 35 CWT steam crane	21.10.36
18559		Firing End Brick Wall	21.10.36
18560		Arrangement of Rear Brick wall	22.10.36
18561	A/B	Blast Pipe	29.10.36
	C	Blast Pipe fitting strip	_
	F/G	Making Up Block (water wall)	_
	D/E	Making Up Block (water wall)	_
18562
18563		Arrangement Pressure Gauge Support bracket	31.10.36
18564	A	Feed Tray	2.11.36
	B/C	Wash Plate Side baffle	_
	D	Wash Plate (rear)	_
	E	Wash Plate (front)	_
	F	Top Feed Delivery Pipe	_
	G	Top Feed Delivery Pipe clip	_
18565
18566		Extra Drilling in Steam Drum	12.11.36
18567		Aggrangement of Firedoor	14.11.36
18568		Ashpan Arrrangement	20.11.36
18569		Arrangement of Firing end screen	20.11.36
18570		Detail of Superheater Top casings	12.12.36
18571	A/D	Damper Door arrangement	21.11.36
	H/J	Firebrick Cover plate	_
	E	Rocker Operating Bar RH	_
	F	Rocker Operating Bar LH	_
	G	Ash Door Catch	_
18572	A	Corner firebar	23.11.36
	B	Wall Firebar	_
	D	Wall Firebar	_
	C	Transverse Rocker Bar 2 - 2 1/2" wide	_
18573	A/E	Side Firebar Support	25.1.36
	F/J	Rocker Firebar Bearer Arrangement	_
	K/Q	Front Firebar support	_
	R	Front and Rear Firebar Bearer	_
	S	Damper Door Shaft lever	_
18574	A	Steam Drum Cleading - rear end	22.1.37
	B	Steam Drum Cleading - rear end	_
	C	Steam Drum Cleading - firing end	_
	F	Main Stop Valve support	_
	D/E	Steam Drum cleading - firing end	_
18575		Damper Door Operating Lever bracket arrangement	31.12.36
	C	Damper Door Hand Lever	_
	D	Retaining collar	_
	A/B	Damper Door Operating Lever bracket	_
	E	Damper door Extension spindle	_
	F	Extension Spindle Bearing bush	_
18576		Asnestos Mattresses	2.12.36
18577
18578		Water Drum Cleading	3.12.36
18579
18580
18581		Ash door knob	9.12.36
18582		Arrangement of Steam Drum Internal Fitting	14.12.36
18583		Ash Chute	1.2.37
18584	A	Bracket for Rocker Gear	17.12.36
	B	Latch for Rocker Operating Bar	_
	C	Clip for Latch	_
	D	Rocker Operating bar extension	_
	E	Spindle for Rocker gear	_
	F	Rivet for Rocker Operating bars	_
	G	Special 3/8" Whit, nut (for superheater clips)	_
	H	3/4" BSP Angle tee	_
18585	A	Inner Superheater Clip - long coil	11.2.37
	B	Inner Superheater clip - intermediate coil	_
	C	Inner Superheater Clip - short coil	_
	D/E	Damper door connecting link	_
18586		Ash Chute	25.8.37
18587
to		The Files between these two numbers appear to be missing
18600
18601		Arrangement of Gear Box	27.10.36
18602	A	Tool Box	28.10.36
	B	Weatherboard Foot angle	_
18603		Water Tank Complete	4.11.36
18604		Arrangement of SD 6 Wheeler with 35 CWT Power operated jib crane	31.10.36
18605	A/B	Steam Colclector pipe	2.11.36
	C	Collector Pipe elbow	_
	D	Superheater Element hook bolt	_
18606	A	Arrangement of Rear Draw B Bkt Stays	2.11.36
	B	Stay Brackets	_
	C/D	Drawbar Stay Bracket	_
18607		Development of Works Heating boiler	4.11.36
18608		1 1/4" Feed Check Valve
18609	A	Tank Steady Bracket	5.11.36
	B	Tank Internal Suction pipe	_
	C	Tank Filler lid	_
	D	Tank filler Top ring	_
	E/F	Filler steady bracket	_
	G	1 1/4" BSP Le Bas Flange	_
	H/J	Exhaust Branch Support and stay	_
18610	A/B	Extra Drilling in Petrol Tank Bracket	4.11.36
	C/D	Stiffening Plate for Petal Tank bracket	_
	E	Mileometer Bracket	_
	F	Tank Support channel	_
	G/H	Tank Side Extension plate	_
18611		Packing of Combustion Channel
18612
18613
18614		Arrangement of SD6 Wheeler with 35 CWT power operated jib crane	4.11.36
18615		Heating Coil Baffle	13.11.36
18616	A/B	Body Side Stiffening channel	12.11.36
	C	Body Side Stiffening channel	_
18617
18618
18619		Arrangement of 4"-7"-6" Comp Engine	25.11.36
18620		S4 Tipper with 10-9 body	18.11.36
18621
18622		Arrangement of Trailer	21.11.36
18623		Arrangement Rear Axle Conversion
18624		Arrangement of Boiler	14.11.36
18625	A/B	Platform Rear Corner angle	24.11.36
	C	Extension Slide	_
	D	Extension Centre Channel	_
	E/F	Platform Front Corner angle	_
	G/H	Cross Chain and Cotter bolt	_
	J	Cross Chain Cotter	_
18626		Part of General Arrangement S Model
18626		Part of General Arrangement S Model
18626 2nd		General Arrangement of Model 'S' waggon	25.11.36
18627		Arrangement of Frame	28.11.36
18628	A/B	Side Channel	28.11.36
	C/D	Rear Spring Channel	_
	E/F	Tank Support channel	_
	G/H	Tank Support Channel cleat	_
	J/K	Platform Support bracket	_
18629	A	Fuel Oil tank	28.11.36
	B	Tank Strap	_
	C	Handhole Cover (oil tank)	_
	D	Cover for Brick quarl	_
18630		Hood	28.11.36
18631	A	Lifting Gear Channel (on frame)	28.11.36
	B/C	Lifting Gear Channel (on hood)	_
	D	Hood Support angle	_
	E/F	Cleat CANCELLED NEVER USED	_
	G	Spare Tyre Location Bracket	_
18632	A	Boss for Lifting Gear Channels	28.11.36
	B/H	Lifting Gear Bearing	_
	C/D/J	Cross Shaft	_
		Collar	_
	F	Lifting Cam	_
	G	Cam Shaft	_
18633	A	Rear Road Wheel Ram	28.8.36
	B	Rear Road Wheel Centre	_
	C	Rear Road Wheel Tyre	_
	D	Rear Road Wheel Tee Pin	_
18634	A	Lifting Gear Lever	4.12.36
	B	Nut	_
	C	Lifting Gear Spindle	_
	D/G	Lifting Gear Spindle bracket	_
	E	Lifting Gear Spindle guide	_
	F	Lifting Gear Cross stay	_
18635		Arrangement of 6/8 Ton Diesel lorry	23.11.36
18636		Arrangement of SD Tractor with Winch star	23.11.36
18637	A	Arrangement of wheel spuds	1.12.36
	B	Spud Joint Link	_
	C	Cage for Brick Quarl	_
	D	Cleat for hood Support angle	_
	E	Rear Spring	_
18638		Reversing Bevel box body	2.12.36
18639	A	Vertical Spindle for rev. Box	4.12.36
	B	Ferrule for vertical spindle	_
	C	Vertical Spindle bush	_
	D	Horizpntal Spindle for rev. box	_
	E	Bush for Horizontal spindle	_
18640		Arrangement of Piping Boiler end	16.3.37
18641		Arrangement of DG tractor	7.12.36
18642	A	Check Valve adaptor	11.12.36
	B	Blanking Off Flange (steam drum)
		pipe flanges
18643		Arrangement of Controls at Artic Bogie	12.12.36
18644		Bonnet	12.12.36
18645	A	Trunnion Joint	12.12.36
	B	Fan Bed-plate Packing	_
	C	Stay Bar Support	_
	D/E	Stay Bar	_
	F	Socket for Hinge Pin (bonnet top)	_
	G	Observation Hole cover (on hood)	_
	H	Support Angle for Fan Bedplate (rear)	_
	J	Support Angle for Fan Bedplate (front)	_
18646		Arrangement of Piping	3.5.37
18647		Arrangement of Dual Control	14.12.36
18648	A	Crosshead Nut	14.12.36
	B	Piston Nut	_
	C	Conn. Rod Bolt Nut	_
	D	Piston Valve Rod nut	_
	B	Special Cap Nut	_
	F	Stuffing Box Nut	_
	H	Special 7/16" BSF Slotted nut	_
	J	Nut for Idler Wheel pin	_
18649		Firegrate Wall bar	16.12.36
18650	A	Throttle Crossover Shaft bracket	16.12.36
	B	Throttle Direction Change Lever	_
	C	Control Lever	_
	E/F	Fulcrum Pin Distance piece	_
	D	Throttle Cross Shaft	_
18651		Cylinder	3.12.36
18652		Valve Motion Arrangement
18653	A	Piston Rod CANCELLED	10.12.36
	B	Piston CANCELLED	_
	C	Wrist Pin	_
	D	Connecting Rod Bolt	_
18654	A	Crosshead	11.12.36
	B	Connecting Rod Bush (big end)	_
	C	Wrist Pin bush	_
18655		Connecting Rod and Cap	11.3.37
18656	A	Conn. Rod Bush liner	15.12.36
	B	Conn. Rod bush shim	_
	D	Weighshaft Bush Liner	_
	E	Weighshaft Bush shim	_
	C	Piston Ring	_
18657		Crosshead Guide	17.2.37
18658		Crankshaft	17.12.36
18659		Crank	29.1.37
18660		Crosshead	30.12.36
18661		Crankcase	4.1.37
18662		Oil Sump	21.4.37
18663	A	Main Bearing Housing - LH	7.1.37
	B	Main Bearing Housing - RH	_
	C	RH MAIN Bearing Hosuing cover	_
	D	Crankcase Top Cover	_
18664		Crankcase Bottom cover	12.2.37
18665	A	Axle Bearing Cap	14.1.37
	B	Axle Bearing Bush	_
	C	Axle Bearing liner	_
	D	Axle Bearing Shim	_
	E	Stuffing box CANCELLED	_
18666		Oil Pump Body	9.4.37
18667	A	Valve Driving Gear Wheel	21.1.37
	B	Valve Idler Gear wheel	_
18668	A	Valve Driven Gear ring	22.1.37
	B	Valve Crank and gear Centre	_
18669	A	Oil Strainer Barrel - sump	6.4.37
	B	Oil Strainer Barrel - delivery	_
	C	Oil Strainer Body - delivery	_
	D/E/H	Oil Strainer Gauze	_
	F/G	Oil Strainer gauze	_
18670	A	Crankcase Side Cover - LH	25.1.37
	B	Crankcase Side Cover - RH	_
	C	Stuffing Box Locking Plate	_
	E	Lubricator Pipe flange	_
	D	Piston Rod Gland Nut CANCELLED	_
18671	A	Valve Crank	25.1.37
	B	Valve crankshaft Cap	_
18672	A	Valve Crankshaft	26.1.37
	B	Valve Crankshaft bush	_
	C	Valve Crankshaft sleeve	_
	D	Main bearing Chip shield	_
	E	Valve Crank pin	_
18673	A	Idler Gear Wheel pin	27.1.37
	B	Idler Pin Distance piece	_
	C	Idler Pin Washer	_
	D	Conn.Rod Pipe Plug	_
	E	Balance Weight Bolt	_
	F/H	Balance Weight dowel	_
	G	Oil Pump Sheave pin	_
18674	A	Cylinder Cover-front CANCELLED	28.1.37
	B	Cylinder Cover -back CANCELLED	_
18675	A	Cyliner Relief Valve Steam pipe	22.3.37
	B	Crank Pin Lubricator Pipe	_
	C	Lubrication pipe	_
	D	Lubrication Pipe	_
		Valve Rod Oil Pipes	_
	G	Oil Pipe Clips	_
18676	A	Balance Weight	1.2.37
	B	Balance Weight	_
18677		Reversing Weighshaft	3.2.37
18678		Oil Distributer box	15.4.37
18679	A	Reversing Weighshaft Slide	11.2.37
		Reversing Crosshead	_
	C	Weighshaft Bearing cap	_
	D	Key - Reversing weighshaft	_
	E	Weighshaft Bearing bush	_
18680	A	Gland Inspection door CANCELLED	10.3.37
	B	Cylinder Relief Valve body CANCELLED	_
18681	A	Weighshaft Slide bolt	5.3.37
	B/D	Pendulum Rod bolt	_
	E/F	Gland Nut Plunger Set pin	_
		Pend Rod Centre pin bolt	_
	C	Oil Pump Conn. Rod - bolt	_
		Crankshaft Bearing housing - bolt	_
	J	Axle Bearing bolt	_
18682		Gland Inspection Door Joint	17.2.37
18683	A	Steam Branch	19.2.37
	B	Exhaust Branch	_
18684	A	Crankshaft Spur	8.2.37
	B	Axle Spur	_
18685	A	Valve Crosshead	22.2.37
	B	Valve Rod Cover	_
18686	A	Piston valve	22.2.31
	B	Valve Rod Cover Adaptor	_
	C	Valve Crosshead guide	_
18687		Oil Pump Connecting Rod and Strap	23.7.37
18688	A/B	Valve Gear Pend Rod and Cap	12.2.37
	C	Valve Crosshead Conn. Rod	_
18689	A	Oil Pump Sheave	25.2.37
	B	Cylinder Relief Valve Pipe Flange (steam) CANCELLED	_
	C	Cylinder Relief Valve Pipe Flange (exhaust front) CANCELLED	_
	D	Cylinder Relief Valve Pipe Flange (exhaust Rear) CANCELLED	_
18690		Piston Valve Liner	12.3.37
18691	A	Cylinder Head cover	1.3.37
	B	Crankcase Top Inspection cover	_
	C	Crankcase Side Top cover	_
	D	Reversing Weighshaft Gitseal housing	_
	E	Reversing Weighshaft Blank cover	_
18692	A	Piston Valve Rod	1.3.37
	B	Adjustment Washer	_
	C	Valve Rod Wrist Pin Bush	_
	D	Valve Crank Pin Bearing Bush	_
	E	Pendulum Rod Centre Bush	_
	F	Pendulum Rod Centre Pin	_
	G	Valve Crosshead Wrist pin	_
18693
18694	A	Pendulum Rod Liner	4.3.37
	B	Pendulum Rod Shim	_
	C	Crosshead Scraper Ring - 9"	_
	D	Valve Crosshead Scraper Ring	_
	E	Valve Cmpression ring	_
18695	A	Arrangement of Cylinder Drain Valve	8.4.37
	B	Cylinder Drain valve body	_
	C	Drain Valve Steam Valve	_
	D	Drain valve cap	_
	E	Stuffing Box Neck ring	_
	F	Stuffing Box Gland	_
	G	Pump Rod Small End Bush	_
	H	Crankshaft Plug	_
18696		Axle Gitseal Housing	17.3.37
18697	A	Oil Filler CANCELLED NEVER USED	19.3.37
	B	Crankshaft Lubricator S?????	_
	C/D	Crankshaft Lubricator and cap	_
	E	Cylinder Relief Valve CANCELLED	_
	F	Cylinder Relief Valve plug	_
18698		Non-Return Valve body	10.4.37
	B	Oil Pipe Bend	_
18699		Cylinder Clothing	25.5.37
18700	A	Arrangement of Cylinder Drain valve	31.3.37
	B	Cylinder Drain valve Body	_
	C	Steam valve	_
	D	Special Coupling nipple	_
		Feather Keys	_
	E	Steam Branch Joint ring	_
18701	A	Oil distribution box cover	25.3.37
	B	Sheave Pin Retaining plate	_
	C	Pump to Filter Packer	_
	D	Oil Filler Blank cover	_
	E	Regulator Support bracket	_
18702		Arrangement of Oil Pump and Filters	2.4.37
18703	A	Cylinder Relief Valve steam pipe CANCELLED	9.4.37
	B	Breather Pipe	_
18704	A	Lubricator Pump Delivery Valve	21.4.37
	B	Pump valve Cap	_
	C	Oil Relief Valve	_
	D	Oil Relief Valve plug	_
	E	Oil Relief Spring pad	_
	F	Oil Relief Adjusting screw	_
18705	A	Relief Valve seat CANCELLED	24.4.37
	B	Breather Valve Plug	_
	C	Breather Valve disc	_
	D	Plug	_
	E	Sump Drain Plug	_
	F/J	Balance Weight stud	_
	G	Drain Plug Washer	_
	H	Dipstick Washer	_
18706	A	Oil Filler elbow	21.4.37
		Non-return valve body	_
	C	Breather Valve nozzle	_
	D	Piston	_
18707	A	Piston Rod	29.4.37
	B	1/2" to 3/4" Special Coupling Nipple	_
	C	Piston Rod Thrust Washer	_
	D	Piston Ass'y strap	_
	E	Piston valve Ass'y strap
18708	A	Cylinder Cover - front	304.37
	B	Cylinder Cover - rear	_
18709	A	Stuffing Box Neck Ring	30.4.37
	B	Stuffing Box Gland	_
	C/H	Special 5/8" Whit. Nut	_
	D	Relief Valve	_
	E	Relief valve cap	_
	F	Relief Valve Distance piece	_
	G	Relief Valve seat	_
	J	Sump Oil Strainer Casing end	_
18710		Arrangement of Crankshaft	6.5.37
18711	A	Arrangement of Cylinder Relief valve	19.5.37
	B	Relief Valve body	_
18712		Arrangement and Detail of test Bed Stands	20.5.37
18713		Test Bed Foundation	20.5.37
18714		Arrangement of Oil Pump	20.5.37
18715	A	Test Shaft for 11"x12" Engine	21.5.37
	B	Test Shaft 9 1/2" x 10" engine	_
18716		Brake drum	24.5.37
18717		Bearing Block and Cap	1.6.37
18718	A	Test Bed Brake Shaft	24.5.37
	B	Bearing Stud	_
		Bearing Block bolt	_
18719		Test Brake half Coupling	26.5.37
18720	A	Coupling Driving bolt	27.5.37
	B	Coupling Driving Bolt bush	_
	D	Brake Spring	_
		Key	_
	C	Brake Lining	_
	G	Brake beam Tie rod	_
18721	A	Bearing Block packer	1.6.37
	B	Reversing Screw Bearing	_
	C	Reversing Screw Bearing	_
	D	Reversing Screw sleeve	_
	E	Reversing Screw sleeve	_
18722		Test Bed Brake Shoe	1.6.37
18723		Brake Shoe	2.6.37
18724		Arrangement of valve Crankshaft	8.6.37
18725	A	Arrangement of Crankcase Breather valves	5.6.37
	B	Arrangement of Valve Idler Gear Wheel	_
18726		Engine Suspension bracket	4.6.37
18727	A	Brake Beam	7.6.37
	B	Brake beam hinge bracket	_
	C	Reversing Link	_
	D/E	Handwheel	_
18728	A to C	Water Scoop	8.6.37
	D/E	Water Inlet Pipe and Bracket	_
	F	Water Scoop bracket	_
	G/H	Water Seal retaining plates	_
18729	A	Brake Trunnion	8.6.37
	B	Hand Wheel Hub	_
	C	Thrust Washer	_
	D	Spring Seat Washer	_
	E	Reversing lever pin	_
	F	Reversing Lever pin Bush	_
18730		Arrangement of Weighshaft	20.7.37
18731		Arrangement of Oil Filters and lubrication Distribution box	22.7.37
18732	A	Cylinder Cover joint	23.6.37
	B	Exhaust Branch to valve Liner joint	_
	C	Joint Oil Pipe Bend to Oil Distribution box	_
	D	Cylinder Relief valve joint	_
	E	Oil distrubtion box cover joint	_
18733
to		The Files between these two numbers appear to be missing